Triac Dimmable LED Driver

Dim your single-colour LED strip properly — match the right TRIAC dimmable LED driver to your existing wall dimmer and eliminate flicker from the start. Most dimming problems trace back to driver selection, not the strip itself.

4.78 943 Reviews

Shop by series

Dim your single-colour LED strip properly — match the right TRIAC dimmable LED driver to your existing wall dimmer and eliminate flicker from the start. Most dimming problems trace back to driver selection, not the strip itself.

Read more

ATOM LED stocks TRIAC dimmable LED drivers in 24V and 48V constant voltage outputs, compatible with standard UK trailing-edge and leading-edge wall dimmers. All units ship from our Telford warehouse with free UK delivery and are backed by manufacturer warranty. Call 01952 370028 if you need sizing help before ordering.

TRIAC Dimmable  ·  24V & 48V Output  ·  Single Colour Strip Only  ·  Trailing-Edge Compatible  ·  Flicker-Free  ·  Free UK Delivery

On this page:

  1. What is a TRIAC dimmable LED driver?
  2. Who should buy a TRIAC dimmable driver — and who should not?
  3. Trailing-edge vs leading-edge dimmers — which works with LED drivers?
  4. How do you size a TRIAC dimmable LED driver correctly?
  5. Why does my dimmable LED strip flicker — and how do I fix it?
  6. How do you wire a TRIAC dimmable driver to a wall dimmer?
  7. Which ATOM LED strips work with TRIAC dimmable drivers in 2026?
  8. How does a TRIAC dimmable driver compare to a non-dimmable driver with controller?
  9. Frequently asked questions about TRIAC dimmable LED drivers
  10. Why buy your TRIAC dimmable LED driver from ATOM LED?

What is a TRIAC dimmable LED driver and how does it work?

A TRIAC dimmable LED driver converts 230V AC mains to low-voltage DC (typically 24V or 48V) while accepting a phase-cut dimming signal from a standard UK wall dimmer switch. The TRIAC circuit inside the dimmer chops the AC waveform to reduce power, and the driver translates that into smooth, proportional brightness adjustment for your LED strip.

Unlike non-dimmable drivers that output a fixed voltage regardless of input, a TRIAC dimmable unit reads the phase angle of the incoming chopped waveform and adjusts its DC output accordingly. This allows brightness control from approximately 1% to 100% using the same dimmer switch you would use for halogen or incandescent lighting in 2026 installations.

  • Input voltage: 220–240V AC mains, standard UK supply.
  • Output voltage: Constant voltage DC — typically 24V or 48V depending on your strip specification.
  • Dimming method: Phase-cut (leading-edge or trailing-edge) via wall dimmer switch.
  • Minimum load: Most TRIAC dimmable drivers require a minimum wattage connected — check the spec sheet before wiring short runs.
  • Compatibility: Single-colour LED strip only — never use with RGB or RGBW strip.

Who should buy a TRIAC dimmable driver — and who should not?

TRIAC dimmable drivers suit homeowners, kitchen fitters, and contractors installing single-colour LED strip who want dimming from an existing or new wall dimmer switch. They are not suitable for colour-changing strip, multi-zone control, or smart-home systems requiring wireless dimming protocols such as DALI or Zigbee.

This driver is for you if:

  • Single-colour strip installation: You are fitting warm white, natural white, or cool white LED strip and want brightness control from the wall.
  • Retrofit dimming: You already have a trailing-edge dimmer switch on the wall and want to connect LED strip to it without rewiring.
  • Simple residential projects: Under-cabinet kitchen lighting, cove lighting, bedroom accent lighting, or staircase strip that needs one-zone dimming.
  • Budget-conscious dimming: A wall dimmer plus TRIAC dimmable driver costs less than a separate controller setup in most 2026 installations.

This driver is NOT for you if:

  • RGB or RGBW strip: Colour-changing strip requires a non-dimmable constant voltage driver paired with a dedicated RGB controller. Using a dimmable driver with RGB strip causes flicker, colour shift, and premature failure of both driver and strip.
  • Multi-zone dimming: If you need different brightness levels in different zones from one driver, you need a non-dimmable driver with a multi-channel Skydance LED controller or Ltech controller.
  • Smart-home integration: TRIAC dimming is analogue phase-cut — it does not communicate with Wi-Fi, Zigbee, DALI, or DMX systems natively.
  • Addressable or digital strip: Addressable digital RGB COB strip uses SPI signal control and requires a dedicated pixel controller.

Common buying mistake: Purchasing a dimmable driver for RGBW strip is one of the most frequent errors we see. The result is unusable flickering at low brightness and uneven colour mixing. Always pair RGBW with a non-dimmable driver and a standalone controller — no exceptions.

Trailing-edge vs leading-edge dimmers — which works with LED drivers?

Trailing-edge dimmers are compatible with most TRIAC dimmable LED drivers and produce smooth, flicker-free dimming across the full range. Leading-edge dimmers were designed for resistive loads like incandescent bulbs and frequently cause flicker, buzzing, and reduced dimming range with LED drivers. Replacing a leading-edge dimmer with a trailing-edge unit costs approximately £15 in 2026.

Feature Trailing-Edge Dimmer Leading-Edge Dimmer
Designed for Electronic transformers, LED drivers Incandescent, halogen, wire-wound transformers
LED compatibility High — works with most TRIAC dimmable drivers Low — frequently causes flicker and buzz
Dimming range Typically 1–100% Often limited to 20–100% with LEDs
Audible noise Minimal Buzzing common with LED loads
Typical UK retail cost (2026) £12–£25 £8–£18
Recommended for LED strip Yes No — replace with trailing-edge

If you already have a leading-edge dimmer and experience flicker after fitting a TRIAC dimmable driver, swap it for a trailing-edge unit before troubleshooting anything else. This single change resolves approximately 80% of LED dimming complaints. Quality trailing-edge dimmers from Varilight, Hamilton, and TCI are widely available from UK electrical wholesalers.

How do you size a TRIAC dimmable LED driver correctly?

Calculate the total wattage of all connected LED strip, then select a driver rated at least 20% above that total. This headroom prevents the driver from running at full capacity, reduces heat, extends lifespan, and ensures stable dimming down to low brightness levels without dropout or flicker.

  1. Step 1 — Measure total strip length: Add together every metre of single-colour strip that will connect to this driver. Include any short linking sections between runs.
  2. Step 2 — Calculate wattage per metre: Check the strip specification — for example, ATOM LED 24V COB strip typically draws 10W/m or 14W/m depending on the density selected.
  3. Step 3 — Multiply length by wattage: 5 metres of 14W/m strip = 70W total load.
  4. Step 4 — Add 20% headroom: 70W x 1.2 = 84W minimum driver rating. Select the next size up — in this case a 100W TRIAC dimmable driver.
  5. Step 5 — Check minimum load: Many TRIAC dimmable drivers require a minimum load of 5–10W to dim smoothly. If your total strip wattage falls below this, the driver may flicker at low dim levels or not turn on at all.
  6. Step 6 — Verify voltage match: A 24V strip must connect to a 24V driver. A 48V strip must connect to a 48V driver. Mismatched voltage will destroy the strip or produce no light.

For projects running long distances, consider 48V strip with a matching 48V LED driver — voltage drop occurs at half the rate of 24V at the same wattage over the same distance, which means more even brightness across longer runs in 2026 installations.

Why does my dimmable LED strip flicker — and how do I fix it?

LED strip flicker with a TRIAC dimmable driver is almost always caused by one of four issues: a leading-edge dimmer instead of trailing-edge, total strip wattage below the driver minimum load, an incompatible dimmer-driver pairing, or the use of a dimmable driver with RGB or RGBW strip. Each has a specific, low-cost fix.

Symptom Likely Cause Fix Typical Cost (2026)
Flicker at all brightness levels Leading-edge dimmer Replace with trailing-edge dimmer ~£15
Flicker only at low brightness Strip wattage below driver minimum load Add more strip or fit a minimum load resistor £3–£10
Strip turns off before dimmer reaches zero Dimmer and driver dimming curves mismatched Try a different dimmer brand or adjust minimum trim (if available) £0–£20
Colour shifting or uneven brightness Dimmable driver used with RGB/RGBW strip Replace with non-dimmable driver + dedicated controller £30–£60
Buzzing or humming from driver Leading-edge dimmer or overloaded driver Switch to trailing-edge dimmer; check total wattage is within driver rating £0–£15

If you have already confirmed trailing-edge dimming and correct minimum load but still experience flicker, contact the ATOM LED technical team on 01952 370028 or email operations@atomled.co.uk — we can check your dimmer and driver models against our tested compatibility list.

How do you wire a TRIAC dimmable driver to a wall dimmer?

The wall dimmer sits between the mains supply and the driver input — it chops the 230V AC waveform before it reaches the driver. The driver then outputs smooth constant-voltage DC to the strip. All mains wiring must be completed by a competent person in accordance with BS7671, and the strip must never be powered while still on the reel.

  1. Step 1 — Isolate the mains supply: Turn off the circuit at the consumer unit and confirm isolation with a voltage tester. Lock off where possible.
  2. Step 2 — Install the trailing-edge dimmer switch: Connect the dimmer to the mains circuit in place of a standard light switch. Follow the dimmer manufacturer's wiring diagram — most UK trailing-edge dimmers use a simple two-wire or three-wire connection.
  3. Step 3 — Connect the driver input: Run the switched live, neutral, and earth from the dimmer switch to the driver's AC input terminals. Use appropriate cable size for the load.
  4. Step 4 — Connect the driver output to the strip: Wire the driver's DC output (+ and -) to your single-colour LED strip using suitable connectors or soldered joints. Ensure polarity is correct.
  5. Step 5 — Uncoil the strip fully before powering on: LED strip must never be powered while coiled — trapped heat destroys adhesive backing, degrades LEDs, and creates a fire risk.
  6. Step 6 — Test the dimming range: Restore power and test the full dimming range from 100% down to minimum. If flicker occurs at low levels, adjust the dimmer's minimum trim pot (where fitted) or check the minimum load requirement.

For longer strip runs, wire multiple strips in parallel back to the driver output — never daisy-chain in series, as series wiring multiplies voltage drop and produces uneven brightness. If you need help planning your wiring layout, call 01952 370028 and speak to the ATOM LED technical team, available Monday to Friday 9am–5pm.

Which ATOM LED strips work with TRIAC dimmable drivers in 2026?

All single-colour ATOM LED COB strip in 24V and 48V is compatible with TRIAC dimmable drivers. This includes warm white, natural white, and cool white in every density and IP rating we stock. RGB, RGBW, and addressable strip must never be connected to a dimmable driver — they require non-dimmable power with a separate controller.

  • 24V single-colour COB strip: Compatible with all 24V TRIAC dimmable drivers — available in 2700K, 3000K, 4000K, and 6000K with CRI90+ across the full range.
  • 48V single-colour COB strip: Pair with a 48V TRIAC dimmable driver for runs up to 30m single feed — half the voltage drop of 24V over the same distance.
  • Outdoor-rated COB strip (IP67/IP68): Fully dimmable with TRIAC drivers, but the driver itself must be installed indoors or in a suitable IP-rated enclosure.
  • ATOM LED custom-cut strip: Cut at marked intervals without voiding the warranty — allows precise fitting to your installation length, and the remaining wattage calculation stays accurate

Not sure which strip to pair? Browse the full dotfree COB LED strip range or call 01952 370028 for a recommendation based on your project.

How does a TRIAC dimmable driver compare to a non-dimmable driver with controller?

A TRIAC dimmable driver dims from the mains side using a wall dimmer switch — simple, low cost, and requires no additional hardware. A non-dimmable driver paired with a low-voltage controller dims on the DC side and supports features like multi-zone control, wireless remotes, and colour changing. Your choice depends on whether you need simplicity or flexibility.

Feature TRIAC Dimmable Driver + Wall Dimmer Non-Dimmable Driver + Controller
Dimming method Mains-side phase-cut (230V AC) Low-voltage PWM (DC side)
Wall switch required Yes — trailing-edge dimmer Optional — remote or app control available
Single-colour strip Yes Yes
RGB/RGBW strip No — causes flicker and colour shift Yes — required method for colour changing
Multi-zone control No — one zone per driver Yes — multi-channel controllers available
Smart-home integration No Yes — Wi-Fi, Zigbee, DALI options
Total component cost (2026) Lower — driver + dimmer only Higher — driver + controller + remote/receiver
Installation complexity Simpler — standard mains wiring Moderate — additional low-voltage wiring

For most residential single-colour installations in 2026 — under-cabinet lighting, cove lighting, bedroom accents — a TRIAC dimmable driver with a trailing-edge wall dimmer is the most cost-effective and reliable approach. If you later decide to add colour changing or multi-zone control, that requires switching to a non-dimmable driver and adding a MiBoxer controller or similar unit.

Frequently asked questions about TRIAC dimmable LED drivers

Can I use a TRIAC dimmable driver with RGB or RGBW LED strip?

  • No — never connect a dimmable driver to RGB or RGBW strip. Colour-changing strip requires a non-dimmable constant voltage driver paired with a dedicated RGB controller. Using a dimmable driver causes flicker, colour shift, and premature failure of both the driver and the strip.

Do TRIAC dimmable drivers work with leading-edge dimmers?

  • Some will function, but performance is typically poor. Leading-edge dimmers were designed for resistive incandescent loads and frequently cause flicker, buzzing, and limited dimming range when used with LED drivers. Trailing-edge dimmers are the recommended choice and cost approximately £15 in 2026.

What happens if my strip wattage is below the driver's minimum load?

  • The driver may flicker at low brightness or fail to turn on entirely. Every TRIAC dimmable driver has a minimum load requirement — typically 5–10W. If your total strip wattage falls below this threshold, either add more strip to the circuit or install a minimum load resistor (available for a few pounds from electrical suppliers).

Can I run two separate strip runs from one TRIAC dimmable driver?

  • Yes, provided both runs are single-colour, the same voltage, and the combined wattage stays within the driver's rated capacity with 20% headroom. Wire the two runs in parallel from the driver's DC output — never in series, as series wiring multiplies voltage drop and produces uneven brightness.

Is a TRIAC dimmable driver suitable for bathroom LED strip?

  • The strip can be dimmable in a bathroom, but the driver must be installed outside the bathroom zones defined in BS7671 — typically outside the room or in a ventilated ceiling void. Pair with IP67-rated strip for zones 1 and 2, and ensure all wiring meets current UK regulations.

How long do TRIAC dimmable LED drivers last?

  • Quality TRIAC dimmable drivers are typically rated for 30,000–50,000 hours of operation. Lifespan depends on ambient temperature, load percentage, and ventilation. Running a driver at 80% of its rated capacity rather than 100% significantly extends its working life — this is why we recommend 20% headroom on every installation.

Can I use a TRIAC dimmable driver outdoors?

  • Most TRIAC dimmable LED drivers are IP20-rated and designed for indoor installation only. If your strip is installed outdoors, the driver should be mounted in a weatherproof IP65+ enclosure or installed indoors with the DC cable run externally to the outdoor strip.

What is the difference between a TRIAC dimmable driver and a DALI dimmable driver?

  • TRIAC dimming uses a standard wall dimmer switch and chops the AC mains waveform — it is analogue and simple. DALI (Digital Addressable Lighting Interface) is a digital protocol that communicates with the driver via a data bus, allowing precise multi-zone control, scene setting, and integration with building management systems. DALI is typically used in commercial projects; TRIAC suits residential and small-scale installations.

Do I need a specific brand of dimmer switch with ATOM LED drivers?

  • Any quality trailing-edge dimmer from a reputable UK manufacturer will typically work. Brands such as Varilight, Hamilton, and TCI are widely tested with LED loads. If you experience issues with a specific dimmer model, the ATOM LED technical team can check compatibility — call 01952 370028 or email operations@atomled.co.uk.

Why buy your TRIAC dimmable LED driver from ATOM LED?

ATOM LED supplies TRIAC dimmable LED drivers from UK stock in Telford, Shropshire — not dropshipped from overseas warehouses. Every driver ships with free UK delivery, and our technical team is available Monday to Friday 9am–5pm on 01952 370028 to help you match the right driver to your strip, dimmer, and installation layout before you order.

  • UK stock, fast dispatch: All drivers ship from our Telford warehouse — most orders placed before 2pm arrive within 1–3 working days in 2026.
  • Free UK delivery: No minimum order for free shipping on all LED drivers and accessories.
  • Technical support before you buy: Not sure which wattage, voltage, or driver type suits your project? Call 01952 370028 or email operations@atomled.co.uk and speak to someone who understands the products.
  • Tested compatibility: We test our drivers with ATOM LED strip to confirm dimming range, minimum load behaviour, and noise levels — so you get a pairing that works out of the box.
  • Complete system supply: Order your driver alongside LED strip, aluminium profiles, and accessories in one delivery.

Ready to order? Browse the full TRIAC dimmable LED driver range, call 01952 370028, or email operations@atomled.co.uk for sizing advice. Free UK delivery on 97% of products.

Why choose ATOM LED for your LED lighting project?

ATOM LED is a UK-based LED lighting specialist stocking every product in our Telford warehouse. We do not dropship from overseas suppliers. Free UK delivery on 97% of products, with typical delivery in 1 to 3 working days. Warranty varies by driver model. Check the individual product page for the exact warranty period.

  • Custom-cut technology: Cut ATOM LED strip at any point without voiding the warranty — no need to find cut marks in tight spaces.
  • CRI90+ on all COB strip: Colours render naturally under ATOM LED strip, making it suitable for kitchens, retail displays, and any application where colour accuracy matters.
  • Technical team available Monday to Friday, 9am to 5pm: Call 01952 370028 or email operations@atomled.co.uk for help with voltage selection, driver sizing, IP ratings, and installation planning.
  • UK stock, not dropshipped: Every product ships from our Telford warehouse. No overseas lead times, no customs delays, no uncertainty on delivery dates.
  • 20m single feed on 24V, 30m on 48V: Longer single-feed runs than most UK competitors, reducing the number of drivers and feed points required in large installations.

Related Collections

Last reviewed: March 2026 — ATOM LED technical team, Telford, Shropshire. Specifications current as of 2026.

🏭 UK LED specialist, Telford, Shropshire  ·  ☎️ 01952 370028  ·  🚚 Free UK delivery on 97% of products

— Verified reviews

Trusted by UK installers and homeowners

4.78
Read all reviews
Verified ★★★★★

Simple to use multi channel faceplate.

Takes a little time to check and setup but worked with their CCt controllers straight away. Simple to use and adjust light settings which was one of the reasons to stick with white. As for longevity, not sure if the unit holds last settings if the batteries need changing. We'll see.

Miboxer K0S 4 Zone CCT rotating panel remote White
Verified ★★★★★

RGB LED rope lights

I was searching for good quality LED rope lights and came across Atom. I ordered 50 mtrs reel of RGBW lights and the item was delivered very quickly and the after sales service has been second to none. Adam has very been helpful with my enquiries every time I have called and it's never to much for him to assist. I would definitely recommend buying from Atom and definitely will do again on my next project.

LED Neon Flex Bendable Aluminium Channel Mounting Track for 10x18mm Neon Flex 1 Metre
Verified ★★★★★

Fabulous

I ordered a specific lengths of ip68 warm white led neon strip for my drive. I installed it as I had installed my other led feature lighting from ATOM and the result was great. Delivered in less than 48hrs the strip was exactly the right length as I had specified. The quality is exceptional and easy to install. The end result justifies the investment and their prices are vey good. Can’t fault them and highly recommend. I will be back for more strip as I have further ideas around my house. Thanks Atom!

Warm White LED Neon Flex 24V 10x20mm IP68 Waterproof 20m
Verified ★★★★★

Superfast delivery, great product!

I ordered 2 controllers for a time-critical installation where I needed to confirm everything was working before completion. I placed the order and the items arrived early the next morning and in time for the installation to be completed! Very grateful for the swift response and attention.

Miboxer 5 in 1 LED Controller (Zigbee 3.0 + 2.4G) Output Max 20A PZ5

  • UK-stocked, never dropshipped
  • Free UK delivery on 97% of products
  • Designed in the UK
  • Up to 7 years warranty

Not sure which light is right for your project?

Call 01952 370028 Email us

Mon–Fri, 9am–5pm · Free UK delivery on 97% of products (Royal Mail 48-hour tracked)