What is the difference between 24V and 12V single colour COB strip?

24V draws half the current of 12V at equal wattage — less voltage drop, thinner cables, and longer runs. 12V maxes out at 5 metres from a single feed. 24V extends that to 20 metres. 12V is for battery-powered applications such as caravans, motorhomes, boats, and van conversions where 12V connects directly without a converter. For any mains-powered installation, 24V is the standard — longer runs, less copper, fewer feed points, and a wider ecosystem of compatible controllers and drivers.

What happens if I exceed the 20-metre single-feed limit?

The strip does not fail or cut out. It continues to work, but the last few metres become measurably dimmer and slightly warmer in colour temperature than the feed end. On a 22m run you might not notice the difference. On a 25m run the difference is obvious to the naked eye. Solutions include injecting power from a second cable at the far end from the same driver, running two separate strips on independent drivers, or stepping up to 48V COB strip for 30 to 50 metre capability.

How do I calculate the right power supply size?

Multiply wattage per metre by total strip length then multiply by 1.25 for 25 percent headroom. Example: 10 metres of 11W/m strip equals 110W times 1.25 equals 137.5W minimum — select a 150W 24V driver. Never run a driver at 100 percent load. At 70 to 80 percent capacity it runs cool, silent, and lasts years longer. For outdoor and unheated spaces, use an IP67-rated driver even if mounted in a sheltered location because condensation damages IP20 drivers over time.

Can I run 24V COB strip around corners without cutting?

Broad curves yes — COB strip is flexible and bends gently around curves wider than about 50mm radius without damage. Sharp 90 degree corners no — cut the strip at the corner point and rejoin with a corner COB strip connector or short soldered wire bridge. IP20 bends more easily than IP67 or IP68 because the silicone jacket adds rigidity. Forcing a sharp bend cracks the copper traces and creates a permanent dead section that cannot be repaired.

Can I use 24V COB strip outdoors through UK winter?

Yes, with IP67 or IP68 strip and an IP67-rated driver. UV-stable silicone jacketing handles sustained rain, frost cycles, snow, and temperatures from minus 20 to plus 50 degrees Celsius without cracking, yellowing, or delaminating. Every joint and cable entry must be sealed with adhesive-lined heat-shrink or IP67 waterproof connectors. Standard push-in connectors corrode within one winter season. ATOM LED uses silicone jacketing which stays flexible in freezing conditions where cheaper PU-coated strips become brittle and crack.

Do I need a separate driver for each strip run?

Not necessarily. One 24V driver can power multiple runs wired in parallel — standard for kitchens feeding four or five under-cabinet strips from one central driver. The advantage is fewer drivers, fewer mains connections, and centralised maintenance. The disadvantage is a single point of failure — if the driver fails all runs go dark. For critical commercial spaces some specifiers prefer one driver per zone for redundancy. Never daisy-chain one run into the next beyond 20 metres — each run connects back to the driver independently.

What is the difference between Triac and PWM dimming?

Triac dimming uses your wall dimmer to control mains voltage into a Triac dimmable driver. Simplest for homes. Requires trailing-edge dimmer as leading-edge causes flicker. PWM dimming uses a controller between driver and strip to adjust brightness by switching the 24V output. Flicker-free to 1 percent or below. App control, scheduling, and multi-zone grouping via MiBoxer or Skydance. Use Triac when reusing an existing wall dimmer. Use PWM when you need deep dimming below 10 percent or app control.

How do I join two sections of 24V COB strip?

Use solderless push-in COB strip connectors for quick joins — straight connectors for end-to-end, corner connectors for 90 degree turns, wire-lead connectors to bridge gaps. Soldered wire leads are more reliable long-term and preferred for any concealed installation behind ceilings or inside pelmets where future access is limited. Push-in connectors rely on spring-clip contact that can loosen in warm environments. For IP67 and IP68 outdoor joints, seal every connection with adhesive-lined heat-shrink to maintain the waterproof rating.

Is 24V single colour COB the right choice or should I consider alternatives?

24V single colour is right when you need white light, runs under 20 metres, and access to the widest range of IP ratings, FreeCut cutting, and controller options. This covers roughly 80 percent of all COB projects in the UK. Consider 48V when runs exceed 20 metres for 30 to 50 metre capability. Consider RGBW when you need colour effects alongside white with a dedicated white channel. Consider 12V when installing in a vehicle, caravan, or boat running from a 12V battery system.

Single Colour COB Strip 24V

Q: Can I use 24V COB strip in a bathroom?

Yes, with IP67 minimum. IP67 handles steam, humidity, and direct water in zones 1 and 2 — above showers, around bath surrounds, and within 600mm of water sources. The driver must always be located outside the bathroom in a dry ventilated space. For wet rooms with constant steam, IP68 provides the highest protection available in the 24V range. 3000K flatters skin tones while 4000K is better for makeup mirrors where colour accuracy matters more than ambience.

Choose the right single colour COB LED strip 24V for your project — warm white, natural white, or cool white in CRI90+ dot-free output. ATOM LED's 24V COB range runs up to 20 metres on a single feed, with FreeCut technology that lets you trim at any point without affecting the warranty.

Every 24V COB strip in this collection delivers CRI90+ colour rendering, a completely dot-free light line, and a 5-year warranty backed by UK-held stock. Available in 2700K warm white through to 6500K cool white, with wattages from 5W/m for accent work up to 20W/m for task and commercial lighting. Free UK delivery on all orders.

24V COB · CRI90+ · FreeCut · Up to 20m Single Feed · 2700K–6500K · 5-Year Warranty · Free UK Delivery

Which colour temperature suits your space?
What wattage per metre do you need?
How far can you run 24V COB strip on one feed?
What driver do you need for 24V COB strip?
How do you dim single colour 24V COB strip?
How do you install 24V COB LED strip?
Where should you NOT use 24V COB strip?
Why choose ATOM LED for 24V COB strip?
Frequently asked questions — single colour COB LED strip 24V

Quick decision summary: If you need a clean, dot-free light line for kitchens, bedrooms, or retail displays under 20 metres total length, 24V single colour COB strip is the right choice. For runs over 20 metres or large commercial spaces, consider 48V single colour COB strip instead.

Who this is for: Electricians, kitchen fitters, interior designers, and homeowners fitting under-cabinet lighting, cove lighting, display case illumination, wardrobe lighting, or bathroom task lighting in 2026 projects.

Who this is NOT for: If you need colour-changing effects, you need RGBW COB strip. If your single run exceeds 20 metres, move to 48V. If you need full outdoor weatherproofing, see the outdoor-rated COB strip collection.

Common buying mistakes to avoid:

Choosing 12V for long runs: Voltage drop on 12V becomes visible after approximately 3 metres, making 24V significantly more practical for kitchen and cove runs in most 2026 installations.
Oversizing wattage: Under-cabinet lighting rarely needs more than 10W/m — overpowering creates glare and excessive heat.
Using a leading-edge dimmer: Leading-edge dimmers cause flicker on most LED drivers; a trailing-edge dimmer typically costs around £15 and solves the problem entirely.

Which colour temperature suits your space?

Single colour COB LED strip 24V is available from 2700K warm white to 6500K cool white. Warm white (2700K–3000K) suits bedrooms, living rooms, and hospitality environments. Natural white (4000K) works well in kitchens and bathrooms. Cool white (5000K–6500K) is typically specified for garages, workshops, and commercial retail displays.

Colour Temperature	Kelvin Range	Best Applications	Mood / Feel
Warm White	2700K–3000K	Bedrooms, living rooms, restaurants, hotels	Relaxed, inviting
Natural White	3500K–4000K	Kitchens, bathrooms, offices, retail	Clean, balanced
Cool White	5000K–6500K	Garages, workshops, task areas, commercial	Bright, alert

2700K warm white: The most popular choice for residential cove lighting and under-cabinet kitchen installations in 2026, delivering a tone similar to traditional halogen.
4000K natural white: Preferred by kitchen designers who want accurate food colour rendering without the warmth shifting how worktops look.
6500K cool white: Rarely used in homes but standard in workshop and commercial display applications where maximum visibility matters.

What wattage per metre do you need?

For accent and mood lighting, 5W/m to 8W/m provides a soft glow suitable for cove details, shelving, and bedroom headboards. Task lighting in kitchens and bathrooms typically requires 10W/m to 14W/m. Commercial and display applications may need 16W/m to 20W/m for high-output illumination across larger surfaces.

More watts means more light and more heat — which is why every COB strip should be mounted on an aluminium profile for heat dissipation.

Application	Recommended W/m	Typical Lumens/m	Heat Management
Accent / mood	5–8W/m	400–650 lm/m	Profile recommended
Under-cabinet task	10–14W/m	800–1,100 lm/m	Profile required
Commercial display	16–20W/m	1,200–1,600 lm/m	Profile essential

Heat and lifespan: Higher wattage strips generate more heat per metre, and without an aluminium profile, the 3M adhesive backing degrades faster, particularly in enclosed spaces like pelmet recesses.
Driver headroom: Always size your 24V LED driver at 80% maximum load — a 5-metre run of 10W/m strip (50W total) needs a driver rated at approximately 63W minimum.

How far can you run 24V COB strip on one feed?

ATOM LED 24V single colour COB strip supports runs up to 20 metres from a single feed point. This is one of the longest single-feed distances available in the UK 24V market in 2026. Voltage drop is managed through higher copper content in the flexible PCB, keeping brightness consistent across the full 20-metre length.

Under 10 metres: Single feed from one end is standard practice, suitable for most kitchen and bathroom installations.
10 to 20 metres: Single feed still works with ATOM LED 24V COB strip — no mid-point injection needed.
Over 20 metres: Consider 48V COB strip with 30-metre single feed, or use parallel wiring with a second feed point on 24V.

For runs approaching 20 metres at higher wattages (16W/m+), check voltage drop calculations with the ATOM LED technical team on 01952 370028 — they can confirm whether single feed or dual feed is the better approach for your specific layout.

What driver do you need for 24V COB strip?

Single colour 24V COB strip requires a constant voltage 24V DC driver. Calculate the total wattage of your strip run (length in metres multiplied by watts per metre), then select a driver rated at least 20% above that figure. For dimming installations, use a TRIAC dimmable driver paired with a trailing-edge dimmer.

Non-dimmable installations: A standard constant voltage 24V driver from the LED power supply range is the most cost-effective option for fixed-brightness applications.
Dimmable installations: Use a TRIAC dimmable 24V driver with a trailing-edge wall dimmer. Leading-edge dimmers frequently cause visible flicker — replacing with trailing-edge typically costs around £15.
Sizing example: A 4-metre run at 14W/m = 56W total load. Apply the 80% rule: 56W / 0.8 = 70W minimum driver rating. A 75W or 100W driver would be the correct choice.

24V DC falls within the SELV voltage threshold under BS7671 (120V DC ripple-free maximum), provided it is supplied from a suitably isolated, safety-rated driver. This classification means significantly reduced shock risk under dry conditions — making 24V the standard choice for residential installations in 2026.

How do you dim single colour 24V COB strip?

Dim single colour 24V COB strip using either a TRIAC dimmable driver with a trailing-edge wall dimmer, or a separate PWM dimmer placed between a non-dimmable driver and the strip. TRIAC dimming is the simpler option for new-build and renovation projects where a wall dimmer plate is already planned.

TRIAC dimming: The driver handles the dimming signal from a standard wall dimmer plate. Ensure the dimmer is trailing-edge; leading-edge types cause flicker on most LED loads.
PWM dimming: A PWM controller sits between the driver and strip. This method offers finer control and is typically used with smart home systems or dedicated LED controllers.
Smart home integration: PWM controllers from brands like MiBoxer and Skydance support app control, scheduling, and scene setting — useful for 2026 projects incorporating whole-house automation.

How do you install 24V COB LED strip?

Installing 24V single colour COB strip requires five core steps: planning your layout and driver position, preparing the mounting surface with an aluminium profile, connecting the strip to the driver, testing the full run before final mounting, and securing all connections. A competent DIYer can complete a typical kitchen installation in approximately 2 hours.

Plan the layout and driver location: Measure the total strip length needed. Position the driver within reach of a fused spur or plug socket. Ensure the driver remains accessible for future maintenance — never seal it inside a closed void.
Prepare the mounting surface: Fix an aluminium profile along the mounting line for heat dissipation and a flat adhesion surface. Never mount strip directly onto bare metal — this can cause short circuits across the exposed PCB traces.
Attach the strip to the profile: Peel the 3M adhesive backing and press the COB strip firmly into the profile channel. Use FreeCut points to trim to exact length — ATOM LED strips can be cut at any point without affecting the warranty. Never power the strip while it is still coiled on the reel, as heat builds up rapidly and can damage both the strip and adhesive.
Wire the strip to the driver: Connect the strip's positive and negative leads to the driver output terminals. For runs approaching 20 metres, use parallel wiring from the driver to multiple strip sections rather than daisy-chaining in series, which multiplies voltage drop.
Test before final fixing: Power up and check for even brightness across the entire run. Verify dimming operates smoothly if a dimmer is fitted. Confirm all connections are secure and the strip sits flat inside the profile.
Fit the diffuser and secure: Clip the profile diffuser cover into place. Opal diffusers provide the smoothest light spread and hide the strip from direct view. Secure any loose wiring with cable clips rated for low-voltage DC circuits.

If you need help planning your installation, call the ATOM LED technical team on 01952 370028 (Monday to Friday, 9am–5pm) or email operations@atomled.co.uk.

Where should you NOT use 24V COB strip?

Standard IP20 rated 24V COB strip must not be used outdoors, in bathrooms within zones 0–2, in steam rooms or saunas, or in any location exposed to direct water contact. It must also not be mounted directly onto bare uninsulated metal surfaces, as exposed PCB traces can short circuit against conductive material.

Outdoor use: Unprotected IP20 strip degrades rapidly when exposed to moisture. Even IP65 (silicone-coated) strip is rated only for surface splashes and is not suitable for typical UK outdoor conditions under BS7671. For outdoor projects, use IP67 or IP68 rated outdoor COB strip.
Bathroom wet zones: Zones 0, 1, and 2 require a minimum of IP67 protection. IP20 strip is only suitable in bathroom zone 3 and above, outside the splash area.
Enclosed unventilated spaces: Fitting high-wattage strip inside sealed pelmets or behind fully enclosed panels without any airflow can cause heat build-up. Always allow some ventilation or use a profile with adequate thermal mass.
Direct metal contact: Never fix strip directly onto bare aluminium, steel, or copper surfaces without an insulating profile channel between the strip and the metal.

Why choose ATOM LED for 24V COB strip?

ATOM LED supplies 24V single colour COB strip from UK-held stock in Telford, Shropshire — not dropshipped from overseas warehouses. Every strip carries a 5-year warranty, CRI90+ colour rendering, and FreeCut technology. The technical team is available Monday to Friday on 01952 370028 to help with sizing, wiring, and driver selection.

FreeCut technology: Cut at any marked point along the strip without voiding the warranty — no fixed cut intervals, no wasted length.
20-metre single feed: Run up to 20 metres from one power point on 24V, reducing the number of drivers and wiring complexity in most residential projects.
CRI90+ across all strips: Colours appear true and accurate under ATOM LED COB strip — critical for kitchen worktops, retail displays, and anywhere colour fidelity matters.
5-year warranty: Covers all COB DC voltage strip. Contact operations@atomled.co.uk for warranty enquiries.
Free UK delivery: Every order ships free across mainland UK, typically arriving within 1–3 working days in 2026.
UK-based technical support: Not a call centre script — speak directly with the team who spec and test these products, Monday to Friday, 9am–5pm.

Frequently asked questions — single colour COB LED strip 24V?

These are the most common questions the ATOM LED technical team receives about 24V single colour COB strip. Each answer is based on real installation experience and UK electrical standards current as of 2026.

Can you cut 24V COB strip to any length?

Yes. ATOM LED 24V COB strip uses FreeCut technology, allowing cutting at any point without voiding the warranty or wasting material on custom-length installations.

Is 24V COB strip safe for domestic use?

Yes. 24V DC falls within the SELV voltage threshold under BS7671 when supplied from a suitably isolated, safety-rated driver. This classification means significantly reduced shock risk under dry conditions, making it the standard voltage for residential LED strip installations across the UK in 2026.

What is the difference between COB and SMD LED strip?

COB (Chip-on-Board) strip uses densely packed micro LEDs beneath a continuous phosphor layer, producing a smooth, dot-free light line. SMD strip uses spaced-apart LED packages that create visible hot spots. COB is the preferred technology for dot-free lighting in 2026 projects.

Do I need an aluminium profile with COB strip?

An aluminium profile is strongly recommended for all installations and essential for strips above 10W/m. The profile acts as a heatsink, extends lifespan, and protects the strip from physical damage. Browse the LED strip profile range for compatible options.

Can I use 24V COB strip in a bathroom?

Standard IP20 strip is only suitable for bathroom zone 3 and above (outside the splash area). For zones 0, 1, and 2, you need a minimum IP67 rating. Check the ATOM LED outdoor and IP-rated ranges for suitable bathroom-rated options.

How many metres of strip can one driver power?

This depends on the strip wattage and the driver rating. Divide the driver wattage by the strip's watts per metre, then reduce by 20% for safe headroom. Example: a 150W driver with 10W/m strip can safely power approximately 12 metres (150W x 0.8 = 120W / 10W/m = 12m).

What accessories do I need for a 24V COB strip installation?

At minimum, you need a 24V constant voltage driver, wire connectors, and an aluminium profile. For dimmable setups, add a trailing-edge dimmer or PWM controller. Browse the full COB strip accessories range for connectors, joiners, and mounting clips compatible with all ATOM LED strip.

Why is 24V better than 12V for most installations?

24V strip experiences approximately half the voltage drop of 12V strip at the same wattage over the same distance. This means brighter, more consistent light output on longer runs. Most professional installers in 2026 specify 24V as the default for any run over 3 metres.

Can I connect multiple strips together?

Yes, using parallel wiring back to the driver. Never daisy-chain in series, as this multiplies voltage drop. Use solderless connectors or solder joints, keeping each section's wires running independently back to the driver terminals.

Does ATOM LED offer free delivery on 24V COB strip?

Yes. All ATOM LED orders ship free to mainland UK addresses, with typical delivery in 1–3 working days. Stock is held in the UK warehouse in Telford, Shropshire — not dropshipped from overseas. Call 01952 370028 or email operations@atomled.co.uk for urgent delivery queries.

Ready to order? Browse the full 24V single colour COB LED strip range above, or contact the ATOM LED technical team for help choosing the right strip, driver, and accessories for your project.

Phone: 01952 370028 (Mon–Fri, 9am–5pm)
Email: operations@atomled.co.uk
Browse drivers: 24V LED drivers
Browse profiles: Aluminium profiles
Browse accessories: LED strip accessories

Related Collections

Last reviewed: March 2026 — ATOM LED technical team, Telford, Shropshire. Specifications current as of 2026.

🏭 UK LED specialist, Telford, Shropshire · ☎️ 01952 370028 · 🚚 Free UK delivery

extra long Warm White 3000K COB LED Strip 24V 480LEDs/m IP20 20m Run

COB Strip

DC 24V LED Power Supply Transformer 100W - 500W IP67 Waterproof - UK LED Lights

Drivers

Controllers

Neon Profiles

Strip Profiles

1 Metre DC 12V/24V RGB LED Strip Extension Cable LED Strip Connector 4 Pin Soldless Strip Jumper Cables Kit with Connector for 5050 3528 - ATOM LED

Accessories

Soft Profile

Mini Neon

Top Bend

COB Strip

Strip Lights

Miboxer

28 products

Let customers speak for us

from 943 reviews

Natural White Neon Flex 16x16mm

The lighting is very good and looks the part in my sons bedroom, what i would say is that they clips provided are poor and dont hold the lighting in place. I purchased some 3m double sided tape and this was much better and maintained the lighting in a straight line.

GARY WALSHAW

Natural White Neon Flex 16x16mm D Shape Top Bend 120LEDs/m 220V 240V IP65 with UK Plug

03/23/2026

LED Neon Flex Aluminium Channel Mounting Track for 8x16mm Neon Flex 1 Metre

Taylor Mcquade

LED Neon Flex Aluminium Channel Mounting Track for 8x16mm Neon Flex 1 Metre

03/15/2026

RGB LED Strip 220V 240V 60LEDs/m IP65 Wireless Bluetooth App Control with Remote

Lights lost om first delivery payed extra for next day emailed and was told they would return next day payment never recieved it, second set was returned by dpd as could not find address was resent out and have now recieved them

Paul Mckinlay

RGB LED Strip 220V 240V 60LEDs/m IP65 Wireless Bluetooth App Control with Remote

03/14/2026

10mm 2-Pin DC Connectors for Single COB LED Strip Light IP67

This product is hard to find on the market.
So glad these guys had it for sale.
Really fast delivery.
I'm very happy.

Alan Wicks

10mm 2-Pin DC Connectors for Single COB LED Strip Light IP67

03/11/2026

Skydance 4 Zones RGB/RGBW Remote Control R8

still waiting for the product , cannot really say its been 3 weeks now.

Luigi Schiavone

Skydance 4 Zones RGB/RGBW Remote Control R8

03/08/2026

24V IP67 Power Supply Driver Constant Voltage 200W

Looks great

Good service

Ali Mehmet

24V IP67 Power Supply Driver Constant Voltage 200W

03/06/2026

These do work, and are easy to install. The clips came with round head screws - don't use them, they must be countersunk. I've docked one star, as if you need a run of these, as I do, there's no way to join them and the cable only goes in at the ends - lucky I have a vertical mill and can cut into the rear midway..!

steve jarman

LED Strip Aluminium Corner Profile Milky Cover Cabinet LED Corner Profile 19x19mm

03/05/2026

LED Strip Light Aluminium Recessed Profile Milky Cover Cabinet LED Channel

Klodi Dabkiewicz

LED Strip Light Aluminium Recessed Profile Milky Cover Cabinet LED Channel

02/27/2026

Warm White 3000K COB LED Strip 24V 384 LEDs/m IP68 Waterproof

Quick help quick order

Klodi Dabkiewicz

Warm White 3000K COB LED Strip 24V 384 LEDs/m IP68 Waterproof

02/16/2026

Add On Extension Cable With UK Plug

Timothy Doyle

Add On Extension Cable With UK Plug

02/09/2026

Excellent customer support received when item unfortunately arrived with opal covering and end caps missing.
Items were sent out immediately for next day delivery. Would definately recommend.

J Melillo

Bendable Plaster in Aluminium Profile Recessed For LED Strip 2 & 3 Metre

02/06/2026

Black Silicone LED Neon Flex Tube Diffuser Body for LED Strip Light 5x13mm

Black led diffuser

This item was perfect for my project. I will be ordering more without question. I asked for some extra endcaps, these were included at no extra cost, great customer service. Thank you A+++++++

Matt Boulton

Black Silicone LED Neon Flex Tube Diffuser Body for LED Strip Light 5x13mm

01/15/2026

Warm White LED Strip 12V 5050 IP65 Waterproof 60LED/m 5 metre

Good quality and price point. Provided a replacement for exactly what I needed

Paul Walker

Warm White LED Strip 12V 5050 IP65 Waterproof 60LED/m 5 metre

01/15/2026

Natural White Neon Flex 220V 240V Wireless 8x16mm 120LEDs/m IP65 Waterproof with UK Plug

Item described as dimmable and even picture shows a dimmer switch and I recieved a wire with none of what was described

jason holden

Natural White Neon Flex 220V 240V Wireless 8x16mm 120LEDs/m IP65 Waterproof with UK Plug

01/06/2026

Cool white neon flex

Installed 17mtr run of cool white neon flex around the canopy shelf of my conservatory. Looks good and gives the added light I was looking for. Good quality product and I would recommend dealing with this company.

Eric Riley

Cool White Neon Flex 220V 240V 8x16mm 120LEDs/m IP65 Waterproof with UK Plug

12/22/2025

Country/region

Single Colour COB Strip 24V

Which colour temperature suits your space?

What wattage per metre do you need?

How far can you run 24V COB strip on one feed?

What driver do you need for 24V COB strip?

How do you dim single colour 24V COB strip?

How do you install 24V COB LED strip?

Where should you NOT use 24V COB strip?

Why choose ATOM LED for 24V COB strip?

Frequently asked questions — single colour COB LED strip 24V?

Can you cut 24V COB strip to any length?

Is 24V COB strip safe for domestic use?

What is the difference between COB and SMD LED strip?

Do I need an aluminium profile with COB strip?

Can I use 24V COB strip in a bathroom?

How many metres of strip can one driver power?

What accessories do I need for a 24V COB strip installation?

Why is 24V better than 12V for most installations?

Can I connect multiple strips together?

Does ATOM LED offer free delivery on 24V COB strip?

Related Collections

COB Strip

Drivers

Controllers

Neon Profiles

Strip Profiles

Accessories

Soft Profile

Mini Neon

Top Bend

COB Strip

Strip Lights

Miboxer

Let customers speak for us

Customer Service

Call Us

Get in Touch

Address

Country/region

Product Comparison