Outdoor LED Strip Lights

Outdoor LED strip lights need to survive UK rain, frost, and condensation, not just look good on the reel. ATOM LED's outdoor range is dotless LED neon flex, a silicone-coated strip that produces one continuous glow with no visible chips, unlike standard LED strip which shows individual dots through the cover. Every reel is IP67 waterproof, built for gardens, decking, driveways, pergolas, pathways, and steps.

Outdoor LED Strip Lights · Dotless Neon Flex · IP67 Waterproof · 24V and 48V · Free UK Delivery · Up to 4 Year Warranty

What makes dotless neon flex different?

Standard outdoor LED strip lights mount individual LED chips with visible gaps between them, so even under a diffuser, a dot pattern shows through, especially on close-range surfaces like steps and pathways. Dotless neon flex encases the LEDs in a solid silicone housing, so the light diffuses evenly before it leaves the strip. There's no chip pattern to hide and no separate profile or diffuser needed for a smooth finish. Browse the full LED neon flex range to compare indoor and outdoor options.

Can you use LED strip lights outdoors?

Yes, provided the IP rating is right for the job. IP67 withstands temporary immersion and handles UK rain, frost, and condensation, making it the practical minimum for permanent outdoor installs. IP65 only protects against splashes from one direction and is not weather rated, a common mistake that leads to early failure. Every strip in this range is IP67 as standard, see the full IP67 neon flex collection for higher density and IP68 options.

What cut intervals and run lengths are available?

• 24V 1cm cut runs up to 15 metres from one end, cut every 10mm, best for steps, risers, and shorter decking runs where precise trimming matters.
• 24V 5cm cut runs up to 20 metres from one end or 40 metres with power fed from both ends, suited to most garden and driveway installs.
• 48V 10cm cut runs up to 40 metres continuous from one end with no mid-run power feed, built for long driveways, garden borders, and perimeter lighting.

Can it bend around corners?

Yes. All three profiles flex around corners, curves, and edges without cracking, kinking, or losing output, so most layouts need no cuts at bends at all.

What colours are available?

2700K warm white gives an amber, relaxed glow for decking and seating areas. 3000K warm white is slightly brighter and the most popular choice for decking and pathways. 4000K natural white suits driveways and utility areas where clarity matters more than atmosphere. 6000K cool white gives bright daylight output for security and commercial applications. Browse single colour neon flex for the full colour temperature range across all voltages.

Which profile do you need?

• 6x12mm is slimline, fits standard aluminium channels, and is available in both 1cm and 5cm cut.
• 8x16mm is wider, giving a broader beam spread and stronger light output for larger areas.
• 10x10mm is a square profile that produces an even 360 degree glow, useful where the strip is visible from multiple angles.

Match the profile to a mounting channel from our neon flex profiles and IP67, IP68 channels collection.

How do you install outdoor LED strip lights correctly?

Installation follows the same core steps whether you're lighting a driveway, decking, or a run of garden steps.

1. Measure the run and choose the matching cut interval and voltage, 24V for most garden and driveway jobs, 48V for continuous runs over 20 metres.
2. Select an IP67 rated driver sized at least 20 percent above total strip wattage, kept in a weatherproof enclosure or indoors with the cable routed out to the strip. Browse 24V and 48V drivers.
3. Cut only at the marked points, then fit waterproof end caps and connectors from our accessories range, an unprotected joint compromises the IP rating of the whole run.
4. Secure the strip with clips or a mounting channel rather than adhesive alone, UK weather affects adhesive bond over time. See neon flex clips.
5. Test the full run before final fixing to confirm even brightness and no flicker.

For longer or multi-zone runs, wire in parallel rather than series, series wiring multiplies voltage drop and dims the far end of the run noticeably.

What mistakes cause outdoor LED strip lights to fail early?

Most early failures come down to a handful of avoidable errors, not faulty product. Get these right and the strip should easily run for years outdoors.

• Choosing IP65 instead of IP67, the most common cause of failure, since splash resistance is not the same as weather resistance.
• Leaving a cut end or connector unprotected, which lets moisture into the strip even when the main run is IP67, so every joint needs a matching waterproof seal.
• Relying on adhesive alone, since UK temperature swings weaken adhesive bonds over months, a mounting channel or clips hold the run securely through a full winter.
• Undersizing the driver, which causes premature failure, always spec at least 20 percent above total strip wattage so it isn't running at its limit in a garden enclosure exposed to heat.

Why choose ATOM LED for outdoor LED strip lights?

ATOM LED builds every outdoor reel to genuinely hold up outdoors, not just carry a waterproof label.

• IP67 rated as standard, with a genuine cut to length warranty on every reel.
• Free UK delivery on 97 percent of products, dispatched within 2 to 3 working days from our Telford warehouse.
• Up to 4 years cover on outdoor LED strip lights.
• A real technical team who can match voltage, cut interval, and profile to your project on the phone, rather than leaving you to guess from a spec sheet.

Ready to buy? Call 01952 370028 Monday to Friday 9am to 5pm, or email sales@atomled.co.uk.

FAQs

How do you connect outdoor LED strip lights? 

Use waterproof push-fit or soldered connectors rated to the strip's IP class, and always fit end caps at any cut point exposed to weather.

Can it be used on outdoor steps? 

Yes, the 24V 1cm cut is designed for this, its close cut spacing allows precise trimming to each step width.

What's the best option for a driveway? 

48V with a 10cm cut for long, continuous perimeter runs, or 24V with a 5cm cut with dual end power for shorter driveways.

Can you install it on a house wall?

Yes, mount in a compatible aluminium profile with an IP67 rated driver positioned undercover or indoors.